Sun. Oct 6th, 2024
    Signal level selection of multi function analogy terminal  14
    0: 0~+ 10 volt please make sure to cut off the over line 1
    1: 0 ~+_10 volt please make sure to cut off the over line 1
    2: 4 ~ +_20 ma  ( 10 bit input )
    frequency (current ) it is effective when b1 _ 01 (frequency command selection ) is set to be 1
    signal level to set frequency command (current )signal .
    Note of setting
    Setting value
    content
    0
    0~+10v input  (10 bit input )
    1
    0~+_10v input (when the voltage is minus ,it will be the operation command which has opposite operation to the operation of the given command )
    2
    4~20ma input
    When used as input voltage terminal ( setting : 0 or  1 , please cut off the over line on the control plate  ( if not the resistor will be burned ) . when voltage input terminal and current input terminal input frequency command simultaneously their summation will be the ultimate command value , in the occasion where voltage terminal and current terminal are used in turn , please set one of the multi function input ( H1_01 ~06 ) to be 1f and this multi function input 1S in off status , the current terminal (14) ,s command will be effective as long as the command from the voltage terminal ( 13 ) is on  , when it is Et as 1 ( 0~ +_ 10 volt  input ) it is necessary that H3_01 is 1 too (0~+_ 10 volt input )

    Setting value
    function
    The content of each function at 100% input
    Control methods
    v/f
    v/f
    with pg
    Open loop vector
    Flux vector
    0
    H3 – 05 , auxiliary frequency command
    Max , output frequency
    0
    0
    0
    0
    H3 – 09 , it cannot be set to be ,0,
    1
    Frequency gain
    The value of frequency command ( voltage)
    0
    0
    0
    0
    2
    Frequency off set  (zero limit when operation direction changes )
    Maximum output frequency (added to h3 – 03 )
    0
    0
    0
    0
    4
    Output voltage off set
    Motor rated voltage (E1-05)
    0
    0
    x
    x
    5
    Time gain of acceleration/ deceleration (reduction ratio)
    The set acceleration time (C1- o1~o8)
    0
    0
    0
    0
    6
    DC braking (DB)current
    Inverter rated current
    0
    0
    0
    x
    7
    Over torque detection level
    Motor rated torque
    0
    0
    0
    0
    8
    Stall prevention level in operation
    Inverter rated current
    0
    0
    x
    x
    9
    Output frequency lower limit level
    Max output frequency
    0
    0
    0
    0
    A
    Prohibited frequency setting
    Max output frequency
    0
    0
    0
    0
    B
    PID feed back
    Max output frequency
    0
    0
    0
    0
    C
    PID target value
    Max output frequency
    0
    0
    0
    0
    D
    Frequency off set
    Note: it is cannot be set simultaneously (opeo7)
    Max output frequency (plus H3 – o3)
    0
    0
    0
    0
    10
    Forward side torque limit
    Motor rated torque
    x
    x
    0
    0
    11
    Reverse operation side torque limit
    Motor rated torque
    x
    x
    0
    0
    12
    Torque limit in regeneration status
    Motor rated torque
    x
    x
    0
    0
    13
    Torque command/torque limit when speed controls
    Motor rated torque
    x
    x
    x
    0
    14
    Torque compensation
    Motor rated torque
    x
    x
    x
    0
    15
    For / rev two sides torque limit
    Motor rated torque
    x
    x
    x
    0
    1f
    H3 – 05 , analog input will not be used
    Max output frequency
    0
    0
    0
    0
    Frequency command (please find function chart for details )

     



    One thought on “winner inverter”

    Leave a Reply

    Your email address will not be published. Required fields are marked *