this becomes the gain to compensate for slip caused by motor temperature variation when motor,the temperature rise by converting it into slip compensation of inverter. its show inverters value.


this function is used to improve speed accuracy when operating with a load .setting range is 0.0~2.5
and factory setting is 1.0 .its setting  very easy from parameters.


this constant dose not normally need to be set . with flux vector control, this becomes the gain to compensate for slip caused by motor temperature variation when motor temperature rises, the motors interior constants change and the slip compensation will be increased . set this constant and adjust the temperature rise by converting it into slip compensation .

this constant can be adjusted when the motors output torque changes at higher temperatures when torque control or limits are used . the larger the setting , the larger the compensation will be set this constant to be 1.0, to compensate the slip set according to rated torque output situation ,for flux vector control , it is used to be motors temperature compensation gain . the motor slip compensation function calculates the motor torque according to the output current and set gain to compensation for output frequency .

this function is used to improve speed accuracy when operating with a load . it is mainly effective with v/f control (without pg). when the control method is switched the factory setting changes as follows v/f control , 0.0, v/f with pg 1.0 open loop vector 0, flux vector 1.0 . when  1.0 is set this function compensation for the rated slip that has been set by the rated torque output .

with flux vector control this becomes the gain to compensate for slip caused by motor temperature variation ,(refer to slip compensation gain , c 3-0 1 under 7.3.6.)the adjustment consequence of slip compensation gain . 1 correctly set the motor rated slip (constant e 2-0 2)and the motor no load current (constant e 2-0 3). the motor rated slip can be calculated by means of the following equation using the numbers that are shown on the motor nameplate .

motor rated slip , motor rated frequency (Hz) rated speed (r/min )x motor (no. of poles )/120 set the values at the rated voltage and rated frequency for the motor no load current . with vector control the motor rated slip is automatically set by auto tuning, 2 set the slip compensation gain (constant c 3- 0 1 to 1.0  if it set to 0.0 slip compensation will be disable). operate with a load measure the speed and adjust the slip compensation gain (in increments of 0.1)when actual speed is low increase the set value when actual speed is high decrease the set value.



  1. Very great post. I just stumbled upon your blog and wanted to say
    that I have really loved browsing your weblog posts.
    After all I will be subscribing to your rss feed and I’m hoping you write once more soon!

  2. What i do not realize is in truth how you’re no longer
    really much more well-favored than you might be right now.
    You’re very intelligent. You realize therefore considerably
    in the case of this subject, produced me for my part consider it
    from a lot of varied angles. Its like women and men don’t seem
    to be interested unless it is something to do with Woman gaga!
    Your individual stuffs excellent. Always maintain it up!

  3. Do you mind if I quote a few of your articles as long as I provide credit and sources back
    to your site? My blog site is in the very same niche as yours and my visitors would genuinely benefit from a lot of the
    information you provide here. Please let me know if this
    ok with you. Appreciate it!

  4. Hi! I just wanted to ask if you ever have any issues with hackers?
    My last blog (wordpress) was hacked and I ended
    up losing months of hard work due to no back up. Do you have
    any solutions to prevent hackers?

  5. An intriguing discussion is definitely worth comment. I do think that you
    ought to publish more about this topic, it might not be a
    taboo subject but usually people do not discuss such issues.
    To the next! Best wishes!!

  6. First off I want to say awesome blog! I had a quick question which I’d like to ask if you
    do not mind. I was curious to know how you center yourself
    and clear your mind before writing. I have had a tough time clearing my thoughts in getting my
    ideas out. I do enjoy writing however it just
    seems like the first 10 to 15 minutes tend to be wasted simply just
    trying to figure out how to begin. Any recommendations or hints?

  7. Thank you for some other excellent article. The place else may anybody get that type
    of info in such a perfect approach of writing?
    I’ve a presentation next week, and I am on the look for
    such info.

  8. I am really impressed with your writing skills and also with the layout on your blog.

    Is this a paid theme or did you customize
    it yourself? Either way keep up the excellent quality writing, it’s rare to
    see a great blog like this one these days.

  9. Fantastic website you have here but I was wondering if
    you knew of any forums that cover the same topics discussed in this article?
    I’d really love to be a part of online community
    where I can get opinions from other experienced individuals that share the same interest.

    If you have any suggestions, please let me know. Thank you!

  10. Greetings I am so glad I found your blog page, I really found you by error, while
    I was searching on Aol for something else, Anyways I am
    here now and would just like to say kudos for a fantastic post and a all round
    thrilling blog (I also love the theme/design), I dont have time to
    browse it all at the minute but I have bookmarked it and
    also added your RSS feeds, so when I have time I will be back to read a
    great deal more, Please do keep up the awesome b.

  11. Excellent beat ! I wish to apprentice while you amend your site,
    how can i subscribe for a blog website? The account aided me a acceptable deal.
    I had been tiny bit acquainted of this your broadcast offered bright clear concept

  12. I believe everything said made a bunch of sense. However,
    what about this? suppose you added a little content?
    I ain’t suggesting your information isn’t good, but suppose
    you added something to possibly get folk’s attention? I
    mean 440 volt inverter slip compensation gain – inverter
    is a little plain. You might peek at Yahoo’s front page and note how they create article titles to get people to open the links.
    You might try adding a video or a picture or two to grab readers
    interested about what you’ve written. Just my opinion, it could make your blog
    a little livelier.

  13. Hello there, I discovered your blog by means of Google whilst searching
    for a similar topic, your site got here up, it
    appears to be like good. I have bookmarked it in my google bookmarks.

    Hello there, just turned into alert to your weblog via Google, and found that it is truly informative.
    I’m going to be careful for brussels. I will appreciate for those who
    continue this in future. Lots of other people will probably be benefited out of your writing.

  14. Greetings from Colorado! I’m bored to death at work so I decided to browse your blog
    on my iphone during lunch break. I love the knowledge you
    provide here and can’t wait to take a look when I get home.
    I’m amazed at how quick your blog loaded on my phone ..
    I’m not even using WIFI, just 3G .. Anyways, awesome blog!

  15. Please let me know if you’re looking for a article author for your site.
    You have some really good articles and I believe I would
    be a good asset. If you ever want to take some of the load off, I’d absolutely love to write some articles for your blog in exchange for a link back to mine.
    Please send me an e-mail if interested. Kudos!

  16. you are in point of fact a excellent webmaster. The website
    loading pace is incredible. It sort of feels that you are doing any
    unique trick. Also, The contents are masterwork.
    you have done a great activity in this matter!

  17. Hello There. I found your blog the usage of msn. This is
    a really smartly written article. I’ll be sure to bookmark it and come back
    to read more of your helpful info. Thank you for the
    post. I’ll certainly comeback.

  18. Thank you for another wonderful post. Where else could anybody
    get that type of info in such a perfect manner of writing?
    I have a presentation next week, and I am on the search for such information.

  19. I drop a leave a response whenever I appreciate a post on a
    website or if I have something to add to the discussion. It’s a result of the passion communicated in the post I
    read. And on this post 440 volt inverter slip compensation gain – inverter.
    I was actually excited enough to drop a thought 😉 I do have a couple
    of questions for you if it’s allright. Could it be only me or does it look like like
    some of these comments come across like written by brain dead folks?

    😛 And, if you are writing on additional online sites, I would like to keep up with you.

    Would you list every one of your shared
    sites like your twitter feed, Facebook page or linkedin profile?

  20. I got this web site from my pal who told me on the topic of this site and at the moment this time
    I am visiting this website and reading very informative articles or reviews at this

  21. Hello this is somewhat of off topic but I was wondering if blogs use WYSIWYG editors or if you have to manually code with HTML.
    I’m starting a blog soon but have no coding experience so I wanted to get
    guidance from someone with experience. Any help would be enormously

  22. Hey There. I found your blog using msn. This is
    a really well written article. I’ll be sure to
    bookmark it and come back to read more of your helpful info.
    Thanks for the post. I’ll certainly return.

  23. Howdy very nice website!! Guy .. Excellent .. Superb ..
    I’ll bookmark your blog and take the feeds additionally?
    I am glad to find numerous helpful information here within the publish, we want develop
    more techniques on this regard, thank you for sharing.
    . . . . .

Comments are closed.